You are here
Post Buckling of Thin Shells
Thu, 2008-10-09 23:56 - Himayat Ullah
It is difficult to conduct post buckling analysis of thin shell under axial compression using Arc Length method in Ansys.
The Minimum & Maximum Arc Length radii are chosen by hit & trial.When imperfections are incorporated in the FE model, some times the solution diverges at a higher critical load that the eigen value buckling, which should be vice versa in actual. Some times , negative eigen values are also shown.
Is there any easy way to solve this nonlinear stability problem?
Himayat
»
- Himayat Ullah's blog
- Log in or register to post comments
- 10361 reads
Comments
Here a good example as a reference
It is indeed difficult to solve the convergence problem for post-buckling FEA solution. The following is a good example and wish a good luck for you!
/PREP7
smrt,off
/TITLE, VM17, SNAP-THROUGH BUCKLING OF A HINGED SHELL
:COM CHANG, C.C.,"PERIODICALLY RESTARTED QUASI-NEWTON UPDATES IN
:COM IN CONSTANT ARC-LENGTH METHOD", COMPUTERS AND STRUCTURES,
:COM VOL. 41, NO. 5, PP. 963-972, 1991.
ANTYPE,STATIC ! STATIC ANALYSIS
ET,1,SHELL63,,1
R,1,6.350 ! SHELL THICKNESS
MP,EX,1,3102.75
MP,NUXY,1,0.3
:COM CREATE FINITE ELEMENT MODEL
R1 = 2540 ! SHELL MID-SURFACE RADIUS
L = 254 ! HALF THE LENGTH
PI = 4*ATAN(1) ! VALUE OF PI COMPUTED
THETA = 0.1*180/PI ! 0.1 RADIANS CONVERTED TO DEGREES
CSYS,1 ! CYLINDRICAL CO-ORDINATE SYSTEM
N,1,R1,90 ! NODES 1 AND 2 ARE CREATED AT POINTS
N,2,R1,90,L ! A AND B RESPECTIVELY.
K,1,R1,90
K,2,R1,(90-THETA)
K,3,R1,90,L
K,4,R1,(90-THETA),L
ESIZE,,2 ! TWO DIVISION ALONG THE REGION BOUNDARY
A,1,3,4,2
AMESH,1
NUMMRG,NODE
:COM APPLY BOUNDARY CONDITIONS
NSEL,S,LOC,Z,0
DSYM,SYMM,Z
NSEL,S,LOC,Y,90
DSYM,SYMM,X
NSEL,S,LOC,Y,(90-THETA)
D,ALL,UX,,,,,UY,UZ
NSEL,ALL
FINISH
:COM SOLUTION PHASE
:COM SINCE THE SOLUTION OUTPUT IS SUBSTANTIAL IT IS DIVERTED TO A
:COM SCRATCH FILE
/OUTPUT,SCRATCH
/SOLUTION
NLGEOM,ON ! LARGE DEFLECTION TURNED ON
OUTRES,,1 ! WRITE SOLUTION ON RESULTS FILE FOR EVERY SUBSTEP
F,1,FY,-250 ! 1/4 TH OF THE TOTAL LOAD APPLIED DUE TO SYMMETRY
NSUBST,30 ! BEGIN WITH 30 SUBSTEPS
ARCLEN,ON,4 ! ARC-LENGTH SOLUTION TECHNIQUE TURNED ON WITH
! MAX. ARC-LENGTH KEPT AT 4 TO COMPUTE AND STORE
! SUFFICIENT INTERMEDIATE SOLUTION INFORMATION
SOLVE
FINISH
/OUTPUT
:COM POSTPROCESSING PHASE
/POST26
NSOL,2,1,U,Y ! STORE UY DISPLACEMENT OF NODE 1
NSOL,3,2,U,Y ! STORE UY DISPLACEMENT OF NODE 2
PROD,4,1,,,LOAD,,,4*250 ! TOTAL LOAD IS 4*250 DUE TO QUARTER SYMMETRY
PROD,5,2,,,,,,-1 ! CHANGE SIGNS OF THE DISPLACEMENT VALUES
PROD,6,3,,,,,,-1
*GET,UY1,VARI,2,EXTREM,VMIN
*GET,UY2,VARI,3,EXTREM,VMIN
PRVAR,2,3,4 ! PRINT STORED INFORMATION
/AXLAB,X, DEFLECTION (MM)
/AXLAB,Y, TOTAL LOAD (N)
/GRID,1
/XRANGE,0,35
/YRANGE,-500,1050
XVAR,5
PLVAR,4 ! PLOT LOAD WITH RESPECT TO -UY OF NODE 1
/NOERASE
XVAR,6
PLVAR,4
Post Buckling of Thin Shells
Pengfei Liu
Thanks a lot for posting a reference example. I am going to run it and will see its convergence behaviour and results.
Himayat
Dear Himayat and
Dear Himayat and Pengfei,
I think the paper attached in the following link might be useful to your problem
http://imechanica.org/node/4124
Dear Pengfei Liu
I would like to ask something about your code above. Your model includes a curved geometry so I think it is not necessary to create initial imperfections on your model. My model is a planar model so I must include initial imperfections. I perform postbuckling analysis after an eigenvalue buckling analysis so in APDL code I need to apply inplane loads two times. One for eigenvalue analysis as 1 unit, other for nonlinear analysis as something higher than critical buckling load. I would like to know is this a correct approach? Or could you suggest an alternative approach for initial imperfections?
Thanks....