- Faculty position in Mechanics of Solids and Structures at Brown University
- 1st International Teaching Staff Week, 02-06 December 2019, Clausthal-Zellerfeld, Germany
- Research Associate (PostDoc) in Dislocation Mechanics Modelling for Nuclear Materials, at Imperial College London
- Contact Angle Hysteresis
- Two open PhD positions in multi-physics process and performance modeling of alloys at the University of Tennessee
- In the 100 000 top scientists there is decline of USA, and a jump of China and India
- Analytical Models for Fatigue Life Prediction of Metals in the Stress-Life Approach -- phd thesis by Pietro D’Antuono
- PhD openings in solid/structural mechanics at Stony Brook University
- Society of Experimental Mechanics 2020 (Orlando, FL) (June 8-11)
- Drastic swelling-induced softening of polymer networks with non-covalent cross-linking bonds

- ABAQUS UMAT
- ABAQUS tutorial
- Cauchy stress
- Geometry & Mechanics
- Large elastic deformation
- Logarithmic strain
- Mechanics of growth
- Mesh-free methods
- Objective rates of stress
- Plastic potential
- Poroelasticity
- Stress and strain
- Temperature
- Timoshenko lectures
- Viscoelasticity
- Why is rubber incompressible?
- Writing a paper
- Writing a proposal
- in situ Mechanics
- tensor
- tensor and its invariants

- this problem in the meanwhile was solved by Persson in 2007. 2 days 23 hours ago
- letter to Nature's editor has been published. 6 days 2 hours ago
- The position is filled. 1 week 3 days ago
- Nobel Prize in chemistry 2019 go to Binghamton University. 1 week 3 days ago
- DOI 1 week 4 days ago
- A letter to the Editor of Nature has been accepted on this 1 week 5 days ago
- however, there is a problem in the present italian system! 2 weeks 1 day ago
- soft robots 2 weeks 3 days ago
- Flexbile Skin for Morphing Wings 3 weeks 4 hours ago
- Hi 3 weeks 2 days ago

- Faculty position in Mechanics of Solids and Structures at Brown University
- Topic 24: Safety in Hydropower
- I share the vision of iMechanica, but am not ready to post anything, should I register?
- Analytical Models for Fatigue Life Prediction of Metals in the Stress-Life Approach -- phd thesis by Pietro D’Antuono
- VMESH
- crack propagation using XFEM
- LS Prepost on Mac
- Deformation Gradient from a deformed mesh - 4 node solid elements
- LS-DYNA error messages
- Structural FEA Internship position available at Schlumberger

## Comments

## Make a code for central crack plate under the impulsive load

Dear,

I want to make a code for central crack plate under the impulsive load by Ansys.

My difficult proplem is make the impulsive loading (Step load) (Trainsient dynamic Full mode) such as the tensile load P(t) = 4000 N/m2 for a plate has a central crack (see above figure), and I want to get the dynamic stress intensity factors with time. I can solve the same problem under static load and I can find the SIFs KI by Ansys. But for impulsive load, I have not yet known to input the load and get DSIFs with time.

So, if every member has the Ansys code such as a plate has a hole under the impulsive loading, please give me to I can read it to learning.

Thank you very much,

Best Regards,

Chau

## Dear Chau, I am also trying

Dear Chau,

I am also trying to solve a similar problem using ANSYS but have been unsuccessful so far at applying an impulse load as well as a static load.

I have done a tutorial which applies a short pulse load to a 1D beam.

My current 2D fracture model is under a static load but ANSYS will not calculate the SIF because I keep getting an error about the x-axis not being parallel to the crack face.

If you have recieived any advice on your problem, can you be so kind as to share the knowledge ? :)

Thank you.

Regards,

Idris

## ANSYS SIF

Dear Idris,

To avoid the "x-axis not being parallel to the crack face" error you may create a local coordinate (LOCAL command) system with the x direction over the symmetry plane pointing to the remaining ligament of the material, the y direction must be oriented in the same direction as the applied load. The origin must be placed at the crack tip.

You can find more detailed information in

Ansys documentation- Structural analysis guide - fracture mechanics - calculating fracture mechanics.A useful tutorial can be found athttp://www.southalabama.edu/engineering/mechanical/faculty/phan/ANSYS_LE...

Unfortunately I have no experience with impulse loads in ANSYS. I hope you find this information useful.

All the best,

Allan Burke

## Same Problem

Dear Chau,

I am facing the same problem as you do. Hope you can advise on how to display mi KI on post26

Thank you

Regards,

Huang

## Ansys

finsh

/clear

L=10

a=6

W=26

radius=0.1*a

nu=0.286

young=76E9

pi=acos(-1)

/Prep7

mp,ex,1,young

mp,nuxy,1,nu

mp,dens,1,2450

et,1,plane82

keyopt,1,3,3

r,1,1

ptxy, 0, 0, -a, 0, -a, L, W-a, L

ptxy, W-a, 0

poly

lesize, 1, , , 10, 8

lesize, 3, , , 10, 1/8

lesize, 4, , , 4

lesize, 5, , , 8

kscon, 5, radius

amesh,1

dl,3,1,symm

dl,5,1,symm

dtran

ANTYPE,TRANS ! FULL TRANSIENT DYNAMIC ANALYSIS

finish

finish

/SOLU

SOLCONTROL,0

KBC,1 ! STEP BOUNDARY CONDITIONS

TIME,1e-2

sfl,2,pres,-100

sftran ! TIME AT THE END OF LOAD STEP 1

NSUBST,50 ! 10 SUBSTEPS FOR TIME STEP OF .0004

OUTPR,BASIC,1 ! PRINT BASIC SOLUTION FOR EACH SUBSTEP

OUTRES,ESOL,1 ! STORE Element SOLUTION FOR EACH SUBSTEP

OUTRES,NSOL,1 ! STORE NODAL SOLUTION FOR EACH SUBSTEP

SOLVE

FINISH

/POST26

NSOL,2,65,U,Y,UY ! STORE UY DISPLACEMENTS OF NODE 1 AGAINST TIME

PRVAR,2 ! PRINT VARIABLE 2 (DISPLACEMENT UY OF NODE 1) V/S TIME

/GRID,1 ! TURN THE GRID ON FOR DISPLAY

/AXLAB,Y,DISPLACEMENT ! MAKE Y-AXIS LABEL AS DISP FOR DISPLAY

PLVAR,2

## Ansys static

L=20

a=4

W=10

radius=0.1*a

nu=0.3

young=210e9

pi=acos(-1)

/Prep7

mp,ex,1,210e9

mp,nuxy,1,0.3

mp,dens,1,7800

et,1,plane82

keyopt,1,3,3

r,1,1

ptxy, 0, 0, -a, 0, -a, L, W-a, L

ptxy, W-a, 0

poly

lesize, 1, , , 10, 8

lesize, 3, , , 10, 1/8

lesize, 4, , , 4

lesize, 5, , , 8

kscon, 5, radius

amesh,1

dl,3,1,symm

dl,5,1,symm

dtran

sfl,2,pres,-1000

sftran

ANTYPE,0

finish

/solu

solve

finish

/OUTPUT

/POST1

ETABLE,SENE,SENE ! RETRIEVE STRAIN ENERGY PER ELEMENT

ETABLE,VOLU,VOLU ! RETRIEVE VOLUME PER ELEMENT

C*** IN POST1 DETERMINE KI (STRESS INTENSITY FACTOR) USING KCALC !**

PATH,KI1,3,,48 ! DEFINE PATH WITH NAME = "KI1"

PPATH,1,46 ! DEFINE PATH POINTS BY NODE

PPATH,2,57

PPATH,3,54

KCALC,,,1 ! COMPUTE KI FOR A HALF-MODEL WITH SYMM. B.C.

*GET,KI1,KCALC,,K,1 ! GET KI AS PARAMETER KI1

## Impule loading with damping ( C = alpha*M+beta*K)

L=20e-3

a=6e-3

W=10e-3

radius=0.1*a

nu=0.3

young=210e9

pi=acos(-1)

/Prep7

mp,ex,1,210e9

mp,nuxy,1,0.3

mp,dens,1,7800

et,1,plane82

keyopt,1,3,3

r,1,1

ptxy, 0, 0, -a, 0, -a, L, W-a, L

ptxy, W-a, 0

poly

lesize, 1, , , 10, 8

lesize, 3, , , 10, 1/8

lesize, 4, , , 4

lesize, 5, , , 8

kscon, 5, radius

amesh,1

!dl,3,1,symm

!dl,5,1,symm

!dtran

nsel,, loc, x, 0.0, W

nsel, r, loc, y, 0.0, 0.0

dsym, symm, y

nsel, , loc, x, -a, -a

dsym, symm, x

alls

ANTYPE,TRANS ! FULL TRANSIENT DYNAMIC ANALYSIS

finish

finish

/SOLU

SOLCONTROL,0

KBC,1 ! STEP BOUNDARY CONDITIONS

ALPHAD,0.00007 ! EQUIVALENT STRUCTURAL DAMPING ALPHA

BETAD,.000000015 ! EQUIVALENT STRUCTURAL DAMPING

TIME,15e-6 ! END TIME

sfl,2,pres,-400 ! PRESS ON THE TOP EDGE OF THE PLATE

sftran ! TIME AT THE END OF LOAD STEP 1

NSUBST,200 ! 200 SUBSTEPS FOR TIME STEP OF .0004

OUTPR,BASIC,1 ! PRINT BASIC SOLUTION FOR EACH SUBSTEP

OUTRES,ESOL,1 ! STORE Element SOLUTION FOR EACH SUBSTEP

OUTRES,NSOL,1 ! STORE NODAL SOLUTION FOR EACH SUBSTEP

SOLVE

FINISH

## Papers on this topic

You might be interested these papers, particularly, the first one.

1. Xie D and Biggers, Jr. SB, Calculation of transient strain energy release rate under impact loading based on virtual crack closure technique,

International Journal of Impact Engineering, 34(2007): 1047-1060.2. Qian Q and Xie D, Analysis of mixed-mode dynamic crack propagation by interface element based on virtual crack closure technique,

Engineering Fracture Mechanics, 74(2007): 807-814.To my experience, most commercial FEA codes didn't implement fracture mechanics in a good manner. So , if you really want to do something on fracture analysis, you'd better develop something yourself. Otherwise, you will continue suffering from using those fracture analysis features provided by commercial FEA codes.

However, if you simply want to get a short assignment done quickly, that's another story.

Good luck!

## Virtual crack closure technique to get DSIFs

Dear Prof, Thank you very much for your respond.I have read two that papers on web

www.sciencedirect.comand it is very important to me because from that i can get the dynamic stress intensity factors (KI and KII). I have the code on C++ which the crack propagates at constant in homogeneous material under mode I loading. This code uses Virtual Crack Closure Technique (VCCT) to get the dynamic stress intensity factors but because for mode I, the energy releases rates is limited by the Rayleigh wave speed (Freund 1990). This code can apply for mixed mode loading of crack propagates at constant speed.So, i want to know why under mode I, why is the crack velocity limited by the Rayleigh wave speed? and if in kinking case, why are we not apply this method (VCCT)? And final, I have not yet understood in your sample in the paper "Analysis of mixed-mode dynamic crack propagation by interface element based on virtual crack closure technique" because if with that initial crack direction, loading and constraints, I think the direction of crack propagation will straight (perpendicular to the right line of the plate). Would you please explain to me some my above wonderings.Thank you very much.## DSIF's

I am not proficient in ANSYS but i have tried calculating the DSIFs using BEM, the DSIFs can be calculated using the crack opening displacements. If you can use ANSYS to determine the crack opening displacements, then you can use the equations to calculate those.

regards,

alan

P.S. I am new in here and hopefully i can learn as well as help here.

## I'll answer you a week later

Chau,

Thank you for interested. Actually, you raised very good questions. Since I'm on leaving to Honolulu for a AIAA confernce, I have no time to response right now. Also let me think a while. Please be back a week later.

Thanks,

De

## Aloha! I'm back and I try to

Aloha! I'm back and I try to answer your questions:

1. So, i want to know why under mode I, why is the crack velocity limited by the Rayleigh wave speed?This is predicted from the math model. For a crack in an inifite body subjected to mode I loading at remote, the crack velocity can be derived based on the energy balance. Two milestones are:

Mott (1948): V=0.38*C0*(1-ac/a)

Freund (1972): V=Cr*(1-ac/a)

V: crack velocity; Cr:Rayleigh Wave speed; C0: dilatational wave speed; a: crack length; ac:initial critical crack length.

If you set crack length "a" to infinity, you can find the crack velocity limits as

Mott: V ->0.38*C0

Freund: V->Cr

Therefore, from Freund's model, the crack velocity is limited by Rayleigh Wave speed. This is what you said.

However, from Mott's model, the crack velocity V is limited by 0.38C0. More test data support Mott's model though, it is the oldest one.

Some other models were also proposed. Recently, Prof. W Yang (Tsinghua University, China) and Prof. H Gao (Plant Max, Germany) did predictions that the crack velocity can exceed Cr. Prof. Rosakis (Caltech, USA) confirmed this throuth tests. If you have further interests, you may consult them.

In brief, the statement of "crack velocity is limited by Rayleigh wave speed" is a math model prediction based on energy balance.

2. and if in kinking case, why are we not apply this method (VCCT)?The popular VCCT works for selfsimilar cracks. In other words, crack must extend along its original orietation. For kinking, the crack suddenly changes its direction, and a modified version of VCCT is needed. Some detailed discussions can be found in my papers, particularly the first one:

1. Xie D, Waas AM, Shahwan KW, Schroeder JA and Boeman RG, Computation of strain energy release rate for kinking cracks based on virtual crack closure technique,

CMES:Computer Modeling in Engineering & Sciences, 6(2004): 515-524.2. Xie D, Waas AM, Shahwan KW Schroeder JA, and Boeman RG, Fracture criteria for kinking cracks in triple material bonded joints,

Engineering Fracture Mechanics, 72(2005): 2487-2504. (Science Direct Top 25 Hottest Articles, #3, Jul-Sep, 2005, #13, Oct-Dec, 2005)3. And final, I have not yet understood in your sample in the paper "Analysis of mixed-mode dynamic crack propagation by interface element based on virtual crack closure technique" because if with that initial crack direction, loading and constraints, I think the direction of crack propagation will straight (perpendicular to the right line of the plate). Would you please explain to me some my above wonderings.Thank you very much.Your thinking is absolutely right. Actually, the test observations support your saying. This is because that cracks always like to propagate in pure mode I locally.

In this example, the crack was forced to grow along a predefined crack path so that make it mixed-mode. In reality when you test it, it may not propagate that way. I chose this example because it was simulated by Profs. Atluri and Nishioka by using their moving singular elements and thus I was able to verify my UEL implementation. And also want to see if this kind of problems can be simulated in a much simpler way.

In brief, this is just simply a math example to verify codeing.

Hopefully my answers could be some kind of help to you.

Good luck!

De

## Thank you very much Prof. Xie De

Thanks a lot for your comments and i will read them. I hope I will get new knowledge from them. Again thanks.

Chau

## I have similar problems

Dear all,

I have similar problem with Chau. I am able to get the stress intensity factor for static loading, but for transient, I was unable to get my stress intensity factor with respect to time using POST26.

Pls advise. Thank You

## Dynamic Stress Intensity Factor

I wanted to get some insight in the transient stress intensity factor (SIF).

In the time history, we notice there is an overshoot (~27%) from the

steady state SIF for a fixed (not propagating crack). I found the

overshoot occurs at the time when the reflected wave from the opposite

crack-tip comes back to the first crack tip. I wanted to know why this

overshoot occurs, what is the physical explanation?

Sandip Haldar

## Can't get ansys to list the results

Hi,

I also have this problem of getting ANSYS to list the results of the stress intensity factors against time,i was wondering whether could anyway give me some tips on how to progress. I am really stuck in a rut. Please help. Your help will be very much appreciated. Thank you.

## crack is open due to loading in the beam in ansys

pls tell me the stepwise procedure to create crack in the beam and also crack open and close in the cantilever beam in ansys mechanical apdl..how u write alogorithm in ansys window to run a program as soon as possible..in my email-swagatmahata.337@gmail.com