## You are here

# Thermal Stress Analysis

Hi Everyone,

I am new to Abaqus. I am working on a research topic where in I need to study the transient thermal stresses, strains arised due to heating a body by thermal radiation. From the user's manual I understood that I need to use "Sequentially coupled thermal-stress analysis" for my model.

I want the sample surface to be heated at a specific rate (say 20 C/min). I am not able to figure out how to set this condition when using "surface radiation" heat transfer or may be at what rate should I change my ambient temperature for the body surface to get heated at the specific rate.

Can anyone please help me in this regard?

Thanks in advance.

## BCs

Hi,

I am not familar with the transient analyis of thermal-mechanical coupled problems. But I guess the question now is concerning about how you specify the boundary conditons, right? Since you do not know the exact surface heat flux as an input, you can not define your "surface radiation" heat transfer...

What I will do:

1) specifiy the temperature rate 20C/min at surface, and check the surface heat flux as a function of time, say q_s(t);

2) release the first BCs and apply q_s(t) at the surface, then you probabilily will end up a rate close to the required value.

3) through this q_s(t), you probably will find a adequate trend to change the ambient temperature.

I just guess this will solve your problem.

## Hi Yixiang, Thanks for

Hi Yixiang,

Thanks for the reply.The solution seems to be good, but how can I specify the temperature rate at the surface and check the surface heat flux. I am new to Abaqus, any suggestion will be very helpful.

Thanks,

- Gopi

## I think stress is a

I think stress is a powerful and a silent killer to those who are stressed.There are many reasons why stress is so disclosed for every woman suffers unfaithful husbands.The internet is buzzing over Jon Gosselin's girlfriend. The reason as to why anyone wants to know anything about Jon Gosselin's girlfriend or the Gosselins in general is because they might not have enough time on their hands, but at any rate, he is already dating again, a 22 year old named Hailey Glassman, and a lot of people are consequently looking for a Hailey Glassman mugshot, as few pictures of her are out there. Jon Gosselin is about to launch his own fashion line – because there aren't enough companies that sell jeans and t shirts. Still, enough people will still flock to payday loan companies if they can buy s shirt designed by Jon Gosselin's girlfriend .

## modeling in abaqus

i am a civil engeenering

i want to modelling a arch dam in abaqus but i have many problems

please help me

i am new in abaqus

i want by program ( matlab ) have many coordinate nodes of geometry dam , but i dont konw use this nodes in abaqus

please help me

## Sequencial Thermal stress analysis

Dear all,

I had one problem while solving the sequencial coupled thermal stress analysis of a disc brake. Can anyone help me the way of calculating the Dflux while solving it in abaqus? I am applying it directly on the disc without considering the pads? this i am applying while doing the thermal analysis? And also how can we applying mass flow rate with change of temp? Your help is highly appreciated?

Thanks

Jobin

## Dear All

I am modelling one part system. I have two materials on that part and i mesh the part as single using tetrahedral elements.

I have a body heat flux and it seems i get continuous temperature and displacement profiles but my stresses are discontinuous where the two material join, i would expect that in case two very different young modulus but the ones i have are very similar.

As i am using a single mesh, considering they a bond, i dont need to use interaction or tie constraints.

Has anybody experienced this situation? Any idea what could be the problem?

Thank you very much

## Hi Roxana, The short

Hi Roxana,

The short answer is most probably you did nothing wrong. That's how most FE packages work. Read on for a bit of an explanation.

Most solid mechanics FE formulations have displacement as the primary variable. Similary for thermal analysis temperature is the primary variable. Now if only the primary variables (not their derivatives) are take to be continuous over elements, you will have a discontinuity in the derivatives even over a homogenous single material. So strains and temperature gradients would be discontinuous, as a result stresses and heat fluxes will be discontinuous too. FE packages do some sort of averaging for stresses on element boundaries or just plot contours based on results on quadrature points so one won't usually notice the discontinuity from post processing results.

If you want stress continuity, you need to use an FE formulation where continuity is enforced on the displacement derivatives too.