You are here
Puzzle: What caused this failure?
Tue, 2008-07-15 02:23 - Biswajit Banerjee
Here's a puzzle for our readers. The following image is of the surface of a failed joint followed by a picture of the joint (not the same one but a similar one) before joining. What material is it? What caused the failure? All manner of speculation is welcome.
Failed joint
Unfailed joint
»
- Biswajit Banerjee's blog
- Log in or register to post comments
- 15930 reads
Comments
for sure failure under torsion --- but
but I am unsure about fatigue, I do not see clearly beach marks
plus what are these buttered circles? corrosion?
tell us more about it. What do you mean joint? Which type of joining? Welding?
Also what are the scales, they seem different in the two pictures?
What is the material -- looks a metal. Why the second 'unfailed' seems neverthless to have cracks?
Many more details for a reasonable descprition are needed to raise the case!
Re: Puzzle
Mike,
I was hoping that some of the younger members of iMechanica would give it a shot before I provided more details.
The failed image has been magnified 6 times, the unfailed one 16 times (my mistake).
The joint is not a weld and the material is not a metal. The unfailed material does not have cracks - those are ridges generated during the cutting process.
-- Biswajit
My guess is that it's an Oreo.
Not even close huh?
That seems reasonable.
I think this is spot on. You can see telltale signs of the torsional failure of the bond between the alternating organic materials. My guess from the failure pattern is that the outer shell was twisted fast, causing a relatively clean failure of the binder. Perhaps this was some sort of preperation for a chemical treatment in a bath of ovine lactic fluid?
Michael, You're spot on
Michael,
You're spot on about the torsion bit. But I'll leave the experiment with ovine lactic fluid to you and then we can compare images on iMechanica.
-- Biswajit
Re: Oreo
Chad,
I assure you that the next time it'll be an Oreo. That thought had never crossed my mind.
-- Biswajit
Re: Puzzle - My Guess
I will do as best as this flaky Drupal and Internet connection allow me to do.
I bet it's a polymer glue and that the failure occurred in torsion (of a rotating rod), sure, but that primarily this happened because the actual cross section failed short of the required strength in torsion.
In the top picture, the circles appearing in the grayish background are due to air entrapment or perhaps, even gas release during polymer setting. The whitish patches in the center is the glue material fractured suddenly in shear. However, it may carry inclusions like crud or dust particles. The glue in the bottom also shows sudden brittle mode fracture. The bottom picture shows the glue applied with a brush, just before the two parts are axially pressed together.
I would bet that the rod material itself was non-polymeric---otherwise, one would expect dissolution of surface layers, and no gas release of this nature.
A reasonable guess would be that either wood or ceramic or metal (likelihood in that order) rods were joined using a synthetic glue, e.g., two parts of the axis of a motor or a hairdrier or a turbine or so, and that the joint failed due to above reason.
-----
No mention of scale, material, whether it's a micro/meso/macro-graph, method of preparation of micrograph... And what else do you expect?
-----
I also felt initially that it could be fatigue. But, fatigue, it's not. There are no progressions characteristics of beach marks. Plus, typically, fatigue cracks grow from only one dominant point on the circumference. Here, the top picture shows a lot of shear walls. So, sure, it's a sudden and brittle failure. But not involving fatigue even in its history. (Plus, the top bubbles are not stretched in one direction, and are too big. So, they can't be dimples. They have to be gas bubbles. My best guess is air entrapment during mixing of the base and the hardner.
Up to you, Biswajit.
Re: Puzzle - Ajit's guess
Ajit,
You analysis is amost absolutely correct. The bottom picture doesn't have any glue on it - that's what the surface looks like just after it's cut (before joining). The ridges are gone in the failed specimen precisely because of dissolution. I took the photographs while testing a light microscope that can (supposedly) magnify to 40x. But given the vibrations in our lab only around 25x is possible.
I took the unfailed picture at a higher magnification to give you an indication of the material. What do you think it is?
-- Biswajit
Wow, Ajit's analysis is very good,I am inclined to accept it!
michele ciavarella
www.micheleciavarella.it
what material is this?
I can not see the attachment, can you upload again?
Re: what material is this?
Linhua,
There is no attachment. Just the two images that you see in the post.
-- Biswajit